Cast-iron-Bowline Step-4

Spilled Hitch-Bowline-Step-4 How to Connect the Spilled Hitch Bowline
Connecting a Bowline using the spilled Hitch method is quick and easy, but it is not a well-known way to tie a Bowline.
The spilled Hitch Bowline can be used to quickly connect a Bowline around an object or, for example, with a Jib or Genoa clew.
You don’t have to remember everything about rabbits and foxes.
The line does about half of the work for you, kind of magic.
When tying a spilled Hitch Bowline, Bowline can be tied up so fast that Bowline wants everyone to show you how to tie it, leaving someone unfamiliar to tying a Spilled Hitch Bowline that clearly looks like “magic.”
Spilled Hitch Bowline, Step One
Spilled Hitch Bowline, Step One.
Start by hovering around the object to which you want to tie the Bowline (or on the strap of the sail if you are attaching a Jib or Genoa sign).
Turn a Half Hitch around the standing part of the line as shown, you can go as you like, but these instructions will be backward if you connect the Half Hitch the other way.
Spilled Hitch Bowline, Step Two
Spilled Hitch Bowline Step Two
Pull down or towards the end of the line, the Half Link must be transferred or poured to stand. Correction of the short section of the line transfers the Half Hitch to the standing side.
Correction of the short section is called spill.
Sometimes you need some help with your fingers to correct Half Hitch and hand over Half Hitch.
Spilled Hitch Bowline, Step 3
Spilled Hitch Bowline, Step 3.
The short section of the line was corrected with Half Hitch transferred to the vertical section of the line.
The rabbit is now walking around the tree for those of you who use this memory method to tie Bowline.
Cover the short section behind the standing section of the line and return along the line that comes along the half line.
Spilled Hitch Bowline, Step 3
Spilled Hitch Bowline, Step Four.
The spilled Hitch Bowline is ready to let loose from the knot.
Gently pull the slack from the Spilled Hitch Bowline.
If necessary, adjust the size of the Bowline by pulling it outside or outside the Bowline’s loop.
Spilled Hitch Bowline, Finished
Finished Spilled Hitch Bowline is connected to a pipe piece, which may be a handrail on a boat, Bull Rail on a Pier or a float.
If you use a Bowline to use a fender to bring the fender to the correct height, adjust the size of the stitch or the amount of streaks on the standing side.
When fastened, a Spilled Hitch Bowline looks like “Magic.. The advantage of using the Spilled Hitch method to tie a Bowline to an object is that the wing spill does most of the work and adjusts Bowline to finish quickly without worry. It’s about whether you’re throwing a loop underhand or underhand to start Bowline.

I wanted to do a tutorial and finally decided on this little macrame bracelet. It is based on the knotted bracelets you see in tourist shops. It is very easy to do and you can design it to suit your style, depending on the beads and beads you choose. They also offer great gifts due to the adjustable length of the sliding buckle.

As long as the bead holes are large enough to accommodate two cords, almost any type of cords and cords work. Only one node is used along a simple square node. The sliding buckle is as simple as finishing, and the whole project can do what you want in part of American Idol or the TV.

You’ll need a few simple things:

  • 4 meter cable (I used C-Lon Tex 400 for this demo)
  • 8 or more beads depending on the length of the bracelet
  • 2 small beads for rockers
  • 3 straight pins
  • scissors
  • Needle tip for finishing needle (has round ballpoint tip)
  • Needle Tip Jewelry Pliers (Optional)
Instructions:

1)Cut the 2-piece strap up to 24,, hold it together and clip about 8 clipboard boards from one end. These will be fill cables. I use a shade of lavender for my stuffing cords.

Cut a piece of cord about 2 meters long. This knot will become ropes. Normally I use the same color cable for both fill and knot cords, but for this demo only, I use a dark purple shade for knot cords. Locate the center of the knot cord, slide it under the filler cables and secure it to the foamcore panel. We will now start to work with square knots with knot cords on the filler cables.

2) I use the right hand, so I usually start with the cable on the right side of the filler cables. Place the fill cords horizontally on the right to form a ring on the right. Take the cable on the left and place it on the horizontal cable, then lift it up under the cables and with the ring on the right. Pull out both knot cables and tighten. This is 1/2 of the square node.

3) Repeat step 2, but take the left cord and place it horizontally on the filler cables that form a loop on the left. Take the right cord and place it on the horizontal cord, then turn it under all the cables and top to left. Pull out both knot cables and tighten. You just made a full-frame knot.

4) After each 3 to 5 square knots, continue to make square knots and place a bead on the filler cables. The number of nodes depends on the size of the cord, the size of the beads, and the fact that many nodes look nice to you. Continue this pattern to the desired length. Note that the sliding clamp will add approximately ″ add.

When you’re done, thread a knot of thread into your needle and sew it to the center as far as possible. If you have problems, use a pair of jewelery pliers to pull your needle. If you find that your knots are too tight and you cannot thread the entire cord, remove the 3-ply cord and sew each thread separately. After properly sewing both knot cables, cut off any excess.

5) Then we make the buckle. Circle your work and hold it together by loosely tying it with a small amount of cord close to both sides of the nodes (I used orange). Foamcore pin bracelet.

Cut a strap about 12 ″ in length. Just like you did in step 1, slide this cord under the four cords and make square knots on all four cords for the 1/2 cord. Finish ends just like you would with a bracelet. When sewing these tips, avoid putting needles into the cords inserted into the needle.

6) Remove these temporary lanyard bits. There are 2 loose cables protruding from both ends of the buckle section. Hold 2 cords together and form a slip knot, place a bead on both cords, then create another slip knot to hold it in place. Cut the excess. Run and show everyone you know.