Make Clew Knot

Clew Knot How-To (With Pictures) – wikiHowwikiHow is a wiki similar to Wikipedia, which means that many of our articles are co-authored by multiple authors. To create this article, volunteer authors have worked to edit and improve it over time. This article has been viewed 51.139 times.
Learn more…
A clew knot is a useful knot that is often used in hammock making. It’s simple to do, but it can be a bit difficult depending on how many lengths you’re connected at the same time, so a good numbering system can help here. In this article, we present a clew knot using twelve half cord; You will need to adjust the measurements according to the number of cables your project requires you to work with.
steps
Episode 1
Start
one
Double the six cable lengths. Attach it to a ring, rod, or other holder shape to hold it in place.
Fasten a larks head with knot.
2nd
Number the cables in your head. Use numbers 1 to 12 and keep the numbering system steady in your mind when working with cables.
If you cannot remember the cable numbers well, use markers such as small plastic toenails with the numbers printed on them – slide them onto the cables, then slide and remove as needed,
3
Disconnect the cables evenly. Pull taut to fix. When the cables run out, you will put them aside when they are no longer needed.
4
Get ready to weave. The fabric moves from left to right, then from right to left and each tool from left to right / right to left must alternate between top / bottom and bottom / bottom. The instructions will clarify this.
Section 2
First weave
one
Knit cord 1 from left to right. Cord # 2, then cord # 3, and so on. Get under it. Continue this weaving motion to the other side.
Section 3
Second knitting
one
This time take the first lanyard # 12 on the right. Route under cable # 11, then through cable # 10. Continue this weaving motion to the left to meet with cord # 2 again.
Chapter 4
Third weave
one
Take cord # 2 and run it over cord # 3. Knit on the right, this time under cord 4. This is an array below the opposite of the first and second rows of braids.
Chapter 5
Fourth knitting
one
Turn left with weaving cord # 11. # 10 until the cord returns to # 3, then under # 9, and so on.
Section 6
Fifth knitting
one
Woven cord # 3 under # 4 cord and # 5 on cord. Continue weaving again using this sequence.
Section 7
Sixth weaving
one
Weaving cable # 10 is under cable 9 and above cable 8. Continue to turn left again using this sequence.
Section 8
Seventh weaving
one
4. lanyard # 4 through lanyard # 5 and lanyard # 6 under webbing. Continue to weave again using this sequence.
Section 9
Eighth weave
one
Woven cord # 9 through cord # 8 and cord # 7 underneath. Continue to turn left again using this sequence.
Section 10
Ninth weaving
one
Cord # 5 under cord # 6 and cord # 7 on, then cord # 8 under webbing.
Section 11
Tenth knitting
one
Lanyard # 8 is woven under lanyard # 7 and on lanyard # 6.
Section 12
Finish
one
Do not wire # 6 and # 7. Pull the # 6 and # 7 ends of both cords to tighten the clutch knot.
2nd
If you attach this knot as part of the hammocks, the loose ends of the cords are connected to each other in the order in which they are knitted.
This means that cables # 6 and # 7 will be attached to the center of the hammock bar or ring.
Connect cables # 8 and # 5, and then connect cables # 9 and # 4.
Connect cables # 10 and # 3, then connect cables # 11 and # 2.
This leaves cables # 12 and # 1 to be connected last.
Community Questions and Answers
The amount of rope depends on the weaving tension. If the tension is loose, it is used more. After weaving the Clew knot, start with a 2-meter long rope to obtain the approximate range of where you end up. Add more than you always think you need, because there’s nothing worse than starting over when there’s not enough rope to make a knot. Depending on the rope thickness, about 5 times the width of the rope is used to make a single knot for binding.
Recently made
Article Info
wikiHow is a Wikipedia benzer wiki,, which means that many articles are co-authored by multiple authors. To create this article, volunteer authors have worked to edit and improve it over time. This article has been viewed 51.139 times.

Macrame Feather Bag Jewelry

 

How to make macrame feather bag charms

Materials:

  • macrame yarn
  • sharp scissors
  • wood beads
  • comb

Steps:

I’ve grown quite a lot of my bag jewelry because I want to make a statement and I love them that way. Remember, my tassels are all pretty big. It’s just the way I like it. If it’s not your job, then you can definitely make them smaller.

I started using a piece of macrame yarn about 20 inches long. Fold it in half and place it on a clean surface as shown below.

You also need two pieces of yarn that are 8 inches long and folded in half.

One of the short sequences should be placed under the longer track as shown in the photo below. You can see the entire stream in my video above.

Place the other short rope on top and pass the ends over the tops. This is actually called a square node.

Pull all of them firmly and push the knot into the desired area so that the ends are the same length.

 

Then knot the base / end of the long string so that the square node can shift from the bottom.

After that you need to keep stacking square knots to get the length you want.

I made my feathers 10 to 12 inches long.

After completing the stacking of the square nodes, you need to remove and scan the macrame thread.

I like to do this part while watching a Netflix show. It calms me down. I know… Weird im

After going all over the macrame feather, you should end up with something you see below.

Now it’s time for a haircut to give a feather shape for wallet jewelry.

Finally you can slip a wooden bead on the end of the rope.

And here you have a very large macrame bag hammer.